How to Hook Up a Water Line to a Refrigerator From the Sink

My husband hates refilling our Keurig. He comments about it often. You see, I have a habit of grabbing my cup, filling it with water, pouring it into the water reservoir and then putting in my k-cup and brewing my coffee. When I go for my 2nd morning cup I again just pour a cup of water before I brew one. It’s never an issue to me. He, on the other hand, when he is ‘off’ or home that morning and drinking more than 1 cup-to-go out the door on the way to work will walk to the Keurig and brew the coffee and walk away. Doesn’t refill it until it’s down low and either has to remove the reservoir and take it to the sink to fill it, or make trips with his little mug s of water from the sink to the counter with the machine. In my mind, no wonder he thinks it’s a big deal.

Ice maker hookup to galvanized pipe

Is an outlet box for fridge ice maker necessary? Right now, I just have a plastic tube coming up out of the floor that goes straight into the fridge. Is it necessary to have an outlet box for my fridge? I have never lived anywhere with one, everyone seems to use the ol’ tube straight into the fridge method. Otherwise, I was just going to connect the hose after the Best Buy guys have left.

That particular outlet box has a sweat connection.

The water line must be purged of air. The icemaker will purge the air by cycling several times before filling with water. The first fill may only be a small amount of water, but .

On BI and BI models, the water line is inserted through the hole in the rear of the unit to connect to the solenoid valve in the front Figure 5. Locate the compression fitting and ferrule packed in the unit. Do not use thread sealing com- pound or tape. Using two wrenches, tighten the compres- sion fitting on the supply line see Figure 6.

Normal operation creates some vibration. A water supply line contacting an internal component or cabinet wall can cause excessive noise during operation or damage to the line. Grille Installation After completing the installation, turn on the water and recheck water connection for leaks. Apply additional tight- ening if needed. Do not use thread sealing compound or tape. Plug in the power cord.

Gently push the unit into position.

How to Install a Water Line for a Refrigerator

How to Install Plumbing for an Ice Maker Refrigerators with automatic ice makers are a great convenience, especially on a hot day. However, there is nothing automatic about getting a water line hooked up to the ice maker. If you are lucky, there will be a hookup in your kitchen wall near the refrigerator. If not, you will need to run a line to the nearest cold water pipe, which is probably in the floor below your kitchen.

Ice Maker Drain Pumps. Brands. DCS GE Ice-O-Matic Lynx Marvel Orien Whirlpool A Condensate Water Pump for KitchenAid Ice Makers. Whirlpool A Sign up for exclusive promo codes, giveaways, and new product alerts.

We are at the tail end of the remodel, finally, and needed to install a water line from the sink plumbing to the refrigerator for the ice maker. This is such an easy process and so I created a tutorial on how to install a refrigerator water line. The instructions apply to replacing an existing water line, as well. An Adjustable Wrench or Pliers Utility Knife First and foremost, if an existing water line is being replaced, turn off the water to the line. It will be located under the sink!

More information may be included on the instructions that are included in the icemaker kit, so make sure to thoroughly read those first! Carefully move the refrigerator out from the wall, and remove any kickplates installed on the lower part of the cabinet on the floor. We built the cabinets in the Rebel house using furniture legs to elevate them off of the floor, and the kickplates had not been installed yet.

If the line is just being replaced, unscrew the brass nut on the valve for the old icemaker line under the sink, and remove the line. I removed the existing line from the refrigerator by unscrewing the brass nut holding the water line in the valve. The line is generally located at the lower right edge of the back of the refrigerator.

It would be easy to add a coupler to tap into the existing line but doing so adds an extra place for a leak to occur. Plus, that part of the line would be located under a cabinet and it may leak for awhile before being detected thus ruining the floor or cabinets.

new refrigerator , ice maker plumbing installation

On ice maker models BI and BI , the water line through the hole in the rear of the unit to connect to the solenoid valve in the front see Figure 3. For recessed installations, allow extra water supply line length to provide slack for easy removal from the recessed area see Figure 7. This will also safeguard against kinking the line. Figure 7 After completing the installation, turn on the water and recheck water connection for leaks. All 75 and 15 Series units are equipped with adjustable feet for level- ing and height adjustment see Figure 9.

Aug 28,  · new refrigerator, ice maker plumbing installation My mother bought a new refrigerator and I was going to hook up the plumbing for the ice maker since her old one didn’t have one. I will have to do it all from scratch because there are no lines to hook up to.

They’re rather cheap – 20 to 30 dollars. For a distance such as yours, it’s best to run the flex line from behind the fridge, down through a small drilled hole in the floor next to the wall, and under the floor. And along the basement ceiling, securing it to the floor joists in the basement ceiling, or drilling holes in the joists – as with running electrical wire.

If the joists are laid in the same direction the hose needs to go, then it is simply secured in place with plastic loops against the side of one joist. When the hose reaches the area in the basement, just under the sink, a cold water pipe probably half inch will be easily accessible. The kit comes with a self tapping valve that will allow the hose to hook up without any tools. It simply clamps on to the cold water pipe and presses a hole in it for the fridge water.

They’re okay, but I never trusted ’em to remain truly leak proof. So I always just make a trip to the hardware store and get the fittings necessary to install a regular valve for this.

Using bottled water for ice maker

How to Install Plumbing for an Ice Maker A refrigerator with an automated ice maker and a built-in water dispenser does absolutely nothing if you do not have a water line to connect to it. You can solve this with an ice maker installation kit that allows you to use the plumbing beneath the sink. The kit provides you with the required parts to hook up a water line to your refrigerator. You may have three water supply lines beneath the sink; two lines connect directly to the faucet while the third line connects to the dishwasher.

But once you’ve bought a refrigerator with a cold water dispenser and automatic ice maker, you’ll still need a way to get water into it. It takes patience, but you can hook a water line up .

Although each refrigerator ice maker is different, they all have basically the same instructions. Speaking of instructions, be sure to read over the instructions that came with your fridge. There may be some specific instructions for your type of ice maker. Ice Maker Installation Kit Since you are reading this, you may have been advised to buy an ice maker installation kit. Although these kits do work, I am not a big fan of the saddle valve that is usually included.

This valve works by piercing an existing copper water line to feed the ice maker.

Your browser is out of date.

Depends on the type s of iron, how much of it there is, whether you have turbidity issues, and the Ph of the water. Only a comprehensive test can determine this. See the link below and notice the explanation concerning the various types of iron and what’s required to remove them. Frequently a chlorinator is essential, but not always.

4. 1/4″ Shut-off valve in water supply line. (Should be Shut-off arm to hang up. 1. Connect A/C power. 2. Locate and repair. 3. Place in normal operation position. * Volts AC is available to the refrigerator and to the Ice Maker. * Water pressure to the Ice Maker is at 15 psi min. – psi max.

This field is for validation purposes and should be left unchanged. Hard water is tough on our skin clothes, hair and makes it difficult to clean dishes and bathroom and kitchen areas. Besides keeping your skin, hair and clothes in better shape, our softener systems can save you big money on water pipe and appliance repairs, clothing replacement, and more. There is something to be said about drinking a crystal-clear glass of great tasting water straight from the tap instead of from a plastic bottle.

But if you think filtered water and purified water is the same thing, think again. Filtration alone merely removes large particulates; purification takes the process further by removing harmful contaminates altogether.

How To Install A Water Line To Your Refrigerator